ZEST BEDWETTING ALARM SUPPORT

Zest bedwetting alarm uses 2 AAA batteries. Always use fresh batteries in your Zest. Do not mix old and new batteries. Do not use rechargeable batteries.

Release the snap-on clip from the back of the alarm unit, insert the batteries (as shown in image below) and close the battery compartment door. The alarm will beep, vibrate and flash a light to signal successful installation. For more detailed instruction refer to your user manual.

Disconnect the sensor from the Zest bedwetting alarm unit during the day. The lights, sounds and vibrations of the alarm unit will stop. The alarm unit enters standby (power save) mode.

Your Zest is designed to have an ultra-long battery life. If the sensor is disconnected from the alarm unit during the day, the batteries should last a year or longer.

It is recommended to continue the treatment until at 14 consecutive dry nights have been recorded.

It is easy to program the Zest bedwetting alarm with one program button that allows you to choose from sound and vibrate, sound (only) and vibrate (only) mode. The alarm doesn’t have an on/off button.

Zest bedwetting alarm has three settings. Press and release program switch once for sound (only) mode, press and release the program button second time for vibrate (only) mode and press and release for third time for sound & Vibrate mode.

Simply clip the alarm unit to the outside of the neckline or place it around your child’s arm with an optional armband accessory (sold separately.

Clip the sensor to the outside of your child’s undergarment, close to the point of urination.

Run the cord under your child’s shirt and insert sensor plug into sensor jack of the alarm unit.

Clip the sensor as close as possible to the point of urination. Fold the cloth by holding it between your fingers and thumbs.

Open the sensor by lifting the lever and insert the folded cloth. Release the lever to secure the sensor on the underwear.

Attach the sensor on the outside of your child’s underwear.

To start monitoring for bedwetting events, insert the sensor plug into the sensor jack. The alarm unit will beep, vibrate and flash a light.

Yes. Of Course! Often parents use diapers with Zest bedwetting alarm as an added precaution to prevent wet and soiled sheets. In case you use diapers, first attach the sensor to the outside of child’s underwear, and then place the diaper over the underwear. Ensure that the sensor is sandwiched between the undergarment and the diaper.

You can buy an extra sensor at the Zest Alarm Store or you can place an order via phone at 408-239-4050.

The Zest Bedwetting Alarm detects low battery. Most likely the batteries of the alarm unit are week and need to be replaced. When the batteries are low the LED lights up. If this is the case, please remove old batteries and replace with new AAA batteries.

Program button is unresponsive in two situations—either you forgot to disconnect the sensor from the alarm unit before programming the alarm or the battery of the alarm unit is running low.

The sensor needs to be washed regularly as urine salts deposit on it over time. The sensor should work once you clean it to remove all deposits. Ensure the sensor is dry before reuse. Please follow these steps to clean the sensor.

Disconnect the sensor from the alarm unit by unplugging the plug from sensor jack.

Use soapy water and a small toothbrush to clean the sensor from inside

Shake the sensor to remove excess water.

Wipe with an absorbent cloth to ensure the sensor is completely dry before reuse.

Reattach the sensor to the alarm unit to begin monitoring for bedwetting events again.

Download the Progress chart here

Monitoring your child’s progress is easy. Every morning when your child wakes up, let them color a box whether they woke up wet or dry. Each day has a small check box; check the box only if your child slept dry through out the night. Do not check the box if the Zest alarm beeped at night. When your child records 14 consecutive dry nights (14 consecutive checks), you may discontinue the treatment.

1. Remove the snap-on clip from your Zest alarm and place the alarm in the comfy-armband pouch.
2. Slide the comfy-armband onto your child’s arm, adjust the strap so it fits comfortably and then secure the Velcro tab. Do not secure the tab too tightly.

You can buy an extra sensor at the Zest Alarm Store or you can place an order via phone at 408-239-4050.

Clean the alarm unit with soft, dry cloth. Do not place the alarm unit under water. If needed, wipe the dry Zest bedwetting alarm with a pre-saturated alcohol wipes to disinfect it.

Disconnect the sensor from the alarm unit by unplugging the plug from sensor jack.

Use soapy water and a small toothbrush to clean the sensor from inside

Shake the sensor to remove excess water.

Wipe with an absorbent cloth to ensure the sensor is completely dry before reuse.

Reattach the sensor to the alarm unit to begin monitoring for bedwetting events again.